毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

AT89C51单片机冲击式动态参数测量系统控制设计

时间:2017-04-08 17:24来源:毕业论文
SH-30806作为步进电机驱动器,AT89C51单片机冲击式动态参数测量系统控制设计,系统硬件设计原理图,系统硬件设计PCB图,系统硬件电路实物图,系统软件程序

落锤式冲击实验可以对各种金属和非金属进行力学性能和工艺性能测试。一直广泛应用于工业领域。本课题主要是根据总体方案要求对冲击式动态参数测量系统控制部分进行设计。对步进电机及其控制系统进行了介绍。根据实际情况选用AT89C51作为硬件核心,选用SH-30806作为步进电机驱动器。本文着重介绍了冲击式动态参数测量系统控制部分的硬件设计及软件编写。用户在LCD上设定高度后,步进电机自动下降到最底端并吸合落锤上升到指定高度将落锤释放,为后续的测量做准备。通过实验验证,检测到结果满足设计要求。6957
关键词  落锤冲击  控制部分  步进电机  硬件设计
毕业设计说明书(论文)外文摘要
Title     The design of the control section of impact dynamic
    parameters measurement system

Abstract The dynamic testing system for parameters of hammer impact can do the test of mechanical and technological properties of various kinds of metal and nonmetal.
  This graduation design focus on the design of of impact dynamic parameters measurement system,according to the overall program requirements. Stepper motor and the control system of stepper motor is introduced. According to the actual situation, I choose the AT89C51 to be the most important part of the hardware. I choose the SH-30806 as the driver of the stepper motor. This thesis focus on the design of the hardware of dynamic testing system for parameters of hammer impact and the software design. After the user set the height on the LCD, the stepper motor decline automatically to the bottom and suck the hammer, then rise to the setted height. It is prepared for the test. After the experiment of the system, the results meet the requirement.
Keywords:  parameters of hammer impact   the section of control
             stepper motor    hardware design
目   次  

1  绪论    1
   1.1  课题背景及研究意义    1
   1.2  国内外研究现状分析    1
   1.3  研究主要内容    3
   1.4  论文结构    3
2  步进电机及其控制系统概述    4
   2.1  步进电机的特点    4
   2.2  步进电机分类    4
   2.3  步进电机工作原理    5
   2.4  步进电机控制系统简介    8
   2.5  本章小结    10
3  冲击式动态参数测量系统控制部分硬件设计总体方案以及关键器件选型    11
   3.1  冲击式动态参数测量系统控制部分硬件设计总体方案    11
   3.2  单片机选型    12
   3.3  步进电机驱动器选型    13
   3.4  本章小结    14
4  系统硬件设计    15
   4.1  硬件系统组成    15
   4.2  系统单片机    15
   4.3  系统外围电路    18
       4.3.1  电源模块设计    18
       4.3.2  LCD显示模块设计    19
       4.3.3  键盘模块设计    21
       4.3.4  电机控制模块设计    22
       4.3.5  通信模块设计    23 AT89C51单片机冲击式动态参数测量系统控制设计:http://www.751com.cn/zidonghua/lunwen_4701.html
------分隔线----------------------------
推荐内容