毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

STC89C52RC单片机的自动浇花系统设计+电路图+程序

时间:2021-05-28 21:13来源:毕业论文
采用STC89C52RC 单片机外接YL-69湿度传感器、LCD显示模块、继电器驱动模块、时钟芯片 、独立按键模块、独立电源,组成电子钟定时自动浇花系统。通过应用独立按键,设置浇花开始时间

摘要: 人们喜欢养花却无暇顾及,针对这个问题,此次设计采用STC89C52RC 单片机外接YL-69湿度传感器、LCD显示模块、继电器驱动模块、时钟芯片 、独立按键模块、独立电源,组成电子钟定时自动浇花系统。通过应用独立按键,设置浇花开始时间,浇花停止时间。当浇花开始时间到,单片机发出浇水指令,电机转动,开始浇水;当到停止时间时,通过单片机程序发出终止浇水指令,电机停转,浇水完成。其过程自动完成,无需人为动作,并且每天循环。67554

毕业论文关键词:STC89C52RC,电子钟,定时自动浇花

Abstract:In daily life, more and more people like to cultivate plants, but too busy to take care of. Aiming at this problem, the design by STC89C52 microcontroller connected YL-69 humidity sensor, LCD display module, a relay driving module, clock chip, independent key module and independent power supply, composed of electronic clock automatic watering system. Through the application of independent keys, set the flowers start time, watering stop time . When the flowers start time to, the SCM sends out instruction of watering, motor rotation, started watering; when to stop time, through the SCM program issued a stop watering instruction, the motor stops rotating, watering. The process is automatically accomplished without human movement, and the daily cycle.

Keywords:STC89C52 , electronic clock,timing automatic watering

目   录

1  绪论 4

1.1课题背景及研究意义 4

1.2本文研究内容 4

2 系统概述 4

2.1整体方案设计思想 4

2.2系统结构及实物图 5

2.3主控芯片的选择 5

2.4传感器模块选择 5

2.5继电器驱动模块选择 6

2.6显示部分 6

3  系统软硬件设计 6

3.1 STC89C52RC单片机 6

3.2 AD转换模块 7

3.3 显示模块 8

3.4 时钟芯片模块 10

3.5继电器驱动模块 10

3.6按键部分 10

3.7电源部分 11

3.8硬件整体设计 11

3.9 系统软件设计思路 12

3.10系统软件设计整体框图 12

结论 14

参考文献 15

致谢 16

附录 17

1    绪论

1.1  课题背景及研究意义

科技的发展导致人们生活水平提高,家里养些花花草草的人也越来越多。因为养花草是一种可以陶冶情操、丰富生活、美化环境的事。要想花草养的好,适量的浇水很重要。有时候人们太忙无暇顾及花草的生长状况。花草的生长问题呢,又80%以上是由花草浇灌问题引起;养植了几个月的花草,就因为浇水不够及时,长势不好,花边枯萎了;不种花,死气沉沉;种花却长得不好看。

所以,利用湿度检测,按时报警供水让花草在无需人们照顾的情况下也能得到定时的浇灌。 STC89C52RC单片机的自动浇花系统设计+电路图+程序:http://www.751com.cn/zidonghua/lunwen_75790.html

------分隔线----------------------------
推荐内容