毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

AT89C51单片机自动风门用光敏探测控制器研制+电路图+程序

时间:2021-04-13 19:49来源:毕业论文
光敏探测部分我们使用光敏二极管结合电压比较器LM393等器件完成对所需信号的采集和初步处理,将光线照度的强弱转换为电平的高低,供控制部分使用;在控制部分,我们将转化来的电

摘要自动风门是在矿井下使用的,目的是阻断风门两侧巷道空气流通,同时又不对矿车和人员的自由通过造成妨碍的一种自动化设备。本设计的最终目的是设计并实现矿用自动风门的完整功能,此设计在本文中分为光敏探测和控制两部分。65539

在光敏探测部分我们使用光敏二极管结合电压比较器LM393等器件完成对所需信号的采集和初步处理,将光线照度的强弱转换为电平的高低,供控制部分使用;在控制部分,我们将转化来的电信号送至单片机AT89C51;再由单片机根据输入的的信号选择我们事先设计好的驱动信号送给输出驱动部分。最终输出驱动部分的作用是将驱动信号转化为步进电机的动作。

在设计过程中我们主要使用Keil uVision作为编程工具,以Proteus作为仿真平台,对本设计的光敏探测部分和控制部分进行仿真。最后使用器件进行实物连接,并成功达到设计要求。最后又提出了扩展功能的可能,进一步丰富了本设计的内容。

毕业论文关键词  自动风门  光敏探测器  24V转5V电源  单片机外部中断

毕业设计说明书(论文)外文摘要

Title  Sensitive detection used for the automatic throttle   controller                                          

 Abstract Automatic damper,used in mine,is an automated device,aimed at blocking the air flow dampers on both sides of the roadway,without interfering with tub and people freely through.The ultimate goal of this design is to design and implement the full functionality of this design,pided into Sensitive detection and signal processing.

We use the photodiode LM393 voltage comparator with other devices necessary to  acquire and process the initial signal,turn the light level into the voltage level,for the use of control section ;In the control section, we will sent electrical signal to the microcontroller AT89C51; Then let the microcontroller choose our pre-designed drive signal to the output drive parts,according to the input signal.Finally output drive stepper motor to complete the appropriate action.

During the design we use Keil uVision to write SCM process,use Proteus as a simulation platform for the verification of the signal acquisition part and the simulation of the signal processing part.After the simulation,requires physical connection and successfully meet the requirements. At last we also raised the possibility of extensions to further enrich the content of this design.

Keywords  automatic throttle  photosensitive detectors  24V switch 5V power supply  external interrupt

目   次

1  引言 1

2  总体功能设计 2

2.1  工作原理设计 2

2.2  系统组成结构 2

3  光敏探测器设计与实现 3

3.1  光敏二极管和光敏三极管 3

3.2  电压比较器 5

3.3  电源模块 6

3.4  光敏探测器部分原理设计 7

3.5  光敏探测器部分原理实现 9

3.6  光敏探测器部分测试 11

4  控制器设计与实现 11

4.1  单片机AT89C51 AT89C51单片机自动风门用光敏探测控制器研制+电路图+程序:http://www.751com.cn/zidonghua/lunwen_73190.html

------分隔线----------------------------
推荐内容