毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

PLC柔性传动的离散目标点简便定位系统设计+主程序

时间:2020-12-29 15:10来源:毕业论文
光电检测电路由槽型光电开关配以一定外围电路组成,能够检测物体是否到达指定位置并将信号输入到PLC中。本文涉及到西门子S7-200 PLC、步进电机、步进电机驱动器的选型与使用以及光电

摘要本文根据柔性传动的离散目标点简便定位系统的功能要求,从硬件及软件两个方面设计了可以实现的系统方案。选用经济、合适的元器件,构建了适用的原理性控制电路。采用西门子S7-200可编程逻辑控制器(PLC)以及光电检测电路来控制型号为86BYG603AA的两相四线混合式步进电机的运转,从而在传动速度约为0.2m/s的同步带传动系统中对目标点进行定位传动,定位传动不确定度小于0.5mm。光电检测电路由槽型光电开关配以一定外围电路组成,能够检测物体是否到达指定位置并将信号输入到PLC中。本文涉及到西门子S7-200 PLC、步进电机、步进电机驱动器的选型与使用以及光电检测电路所需元器件的选型与电路的搭建等。61410

毕业论文关键词:光电检测电路  S7-200 PLC  两相四线混合式步进电机   

毕业设计说明书(论文)外文摘要

Title    The design of simple discrete target positioning system of flexible transmission

Abstract According to the requirements of simple discrete target positioning system of flexible transmission ,this paper designs a practical system scheme from hardware and software. An applicable principle control circuit is built by choosing cheap and suitable components.And the  programmable logic controller (PLC) of Siemens S7-200 and the photoelectric detection circuit are used to control the operation of the two-phase four-wire hybrid stepping motor of 86BYG603AA, so as to locate and transmit the target points in the synchronous belt transmission system, whose speed is about 0.2 meters per second, and to make the uncertainty of positioning transmission is less than 0.5 mm. The Photoelectric detection circuit is composed of trough type photoelectric switch and some peripheral circuits. It is capable of detecting whether objects could reach the specified location and inputting signals to the PLC. This paper involves the selection and use of the Siemens S7-200 PLC, stepper motor, and stepper motor drives, and the selection of required components  for photoelectric detection circuit and its building and so on.

Keywords: photoelectric detection circuit, S7-200 PLC, two-phase hybrid stepping motor.

1. 绪论 1

1.1  设计背景 1

1.2  同步带类柔性传动定位系统的研究与发展现状 1

1.3  本次柔性传动定位系统设计要完成的任务 2

2. 柔性传动的离散目标点简便定位系统方案设计 2

2.1  柔性传动定位系统概述 2

2.2  总体方案设计 3

3  主要器件选择 4

3.1  步进电机的选型 4

3.2  步进电机驱动器的选型及应用设计 7

3.3  PLC的选型 8

3.4  光电开关的选型及应用设计 10

4.  柔性传动的离散目标点简便定位系统硬件集成 12

4.1  定位系统的硬件接线 12

4.2  定位系统软件设计I/O地址分配 13

5.  柔性传动的离散目标点简便定位系统软件设计 14

5.1  控制软件的设计思路 14

5.2  定位控制系统编程 16

5.3  定位系统调试 PLC柔性传动的离散目标点简便定位系统设计+主程序:http://www.751com.cn/zidonghua/lunwen_67166.html

------分隔线----------------------------
推荐内容