毕业论文

打赏
当前位置: 毕业论文 > 自动化 >

MATLAB循环流化床控制系统的仿真设计

时间:2016-11-22 19:39来源:毕业论文
首先做了循环流化床锅炉的简介和介绍其特性. 再大致说明了循环流化床控制系统的整体方案做出相应部分的仿真模型

摘要:本课题的研究对象是循环流化床统自动化系统。探讨循环流化床锅炉的控制系统中各部分的控制策略。在此基础上,建立了MATLAB仿真模型,并在传递函数模型中加入扰动,以验证控制策略的可行性,修正和优化控制参数。本文首先做了循环流化床锅炉的简介和介绍其特性. 再大致说明了循环流化床控制系统的整体方案,以及运用到的一些主要软件。并同时对应控制方案,做出相应部分的仿真模型,并进行分析修正。最后对组态界面的功能和构成做出了详细的解释。实验表明设计结果满足设计指标的要求,具有一定的超前预研特点。

关键词: 循环流化床;MATLAB仿真;模糊控制;扰动;WinCC
The simulation design of CFBB control system
Abstract: The subject is the simulation design of CFB control system. Explore the control strategy of each part of circulating fluidized bed boiler control system. On this basis, the establishment of a MATLAB simulation model and adding disturbance transfer function model to verify the feasibility of the control strategy, fix and optimize control parameters. Firstly, do an introduction of circulating fluidized bed boiler and presentation of its features. Then broadly describes the overall program of circulating fluidized bed control system, as well as applied to some of the major software. While the corresponding control scheme, make the appropriate part of the simulation model and analyze corrected. Finally, the functions and composition of the configuration interface to make a detailed explanation. The experiment design results show that the requirement to meet design specifications, with some characteristics of advance research.

Key words: CFBB; The simulation OF MATLAB; fuzzy control;distribution;WinCC
    目录
1    研究背景    3
1.1    循环流化床锅炉简介及工作原理    3
1.2    循环流化床锅炉的特性    3
1.3    循环流化床锅炉的发展现状    5
1.4    选用计算机仿真的依据    7
1.5    本文主要内容    7
2    循环流化床锅炉控制的整体方案    7
2.1    循环流化床锅炉主要控制任务    7
2.2    控制模型结构控制框图及相应结论    8
2.3    过热蒸汽温度控制    9
2.4    流化床温、负荷控制    10
2.5    炉膛压力控制    11
2.6    汽包液位控制    12
2.7    除氧器液位控制    13
3    软件概述    13
3.1    WINCC、STEP7、WINLC的特点    14
3.2    SIEMEMS STEP7的模块    14
3.3    WINAC BASIS特点和选用依据    15
4    仿真模型的建立    16
4.1    蒸汽温度模型    17
4.2    炉膛负压的仿真模型    18
4.3    汽包液位模型    19
4.4    除氧器液位控制模型    20
4.5    燃烧控制系统仿真模型    21
4.6    氧量控制模型    24
5    仿真模型的嵌入和组态界面    25
5.1    仿真模型的嵌入    26
5.2    组态界面的构成与功能    27
6    总结    33 MATLAB循环流化床控制系统的仿真设计:http://www.751com.cn/zidonghua/lunwen_154.html
------分隔线----------------------------
推荐内容