毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

暖风风洞挡板塑料模设计+CAD图纸

时间:2018-06-09 19:38来源:毕业论文
模具采用一模四腔的设计方案。然后针对该方案进行了重点论述,主要包括分型面选定和流道设计和冷却水道布置及其注塑模的设计过程、注塑模主要零部件的设计要点等

摘要:本设计是对一般精度智能便座产品上的暖风风洞挡板塑件进行模具设计,给定的材料为PP且是小尺寸件。在考虑到了经济性、零件的成型工艺性以及复杂程度等诸多因素的基础上进行成型工艺分析与计算的。文中还对注塑模具成型零件和其他相关零件的选择原则及选择方法进行了说明。期间要参考大量与注塑模相关的资料和翻阅各种手册,并通过计算以确定模具结构及尺寸,通过不段的计算与修改,并在指导老师的悉心关怀和耐心指导下进行不间断的反复修改,最终确定画出了装配图和零件图。23979
确定暖风风洞挡板的设计方案,该模具采用一模四腔的设计方案。然后针对该方案进行了重点论述,主要包括分型面选定和流道设计和冷却水道布置及其注塑模的设计过程、注塑模主要零部件的设计要点等。
毕业论文关键词: CAD 建模,矩形侧浇口一模四腔,注塑模具设计
Inject mold Design of Yue Kang Intelligent sanitary ware warm wind tunnel flap
Abstract: This design is for a given material for PP small size, the general accuracy of the for the intelligent sanitary ware warm wind tunnel flapmould design. In consideration of the economy, parts of the molding technology and complexity, and many other factors in the molding process on the basis of the analysis and calculation. It also of injection mold shaping parts, and other related parts to illustrate the selection principle and selection method. During to refer to a lot of useful information related to injection mold and leaf through all kinds of manual, And in guiding the teacher's careful care under the guidance and patience to constantly modify again and again.
Make sure the design of the ware warm wind tunnel flap, namely the mould with one module and four cavities, side core-pulling design scheme. Then focuses on the solution, this paper mainly includes the side core-pulling of plastic parts and injection mold design process, key points of injection mold design of main components.
Key words: CAD modeling; rectangular side of the gate with A four-mode
目  录
 1  概述 1
1.1  课题来源 1
  1.2  课题的研究目的 2
2 塑件结构工艺性分析 3
2.1  塑件造型3
  2.2  塑件分析 4
    2.2.1 塑件设计要求  4
    2.2.2 塑件结构分析  4
2.2.3  脱模斜度   4
  2.3 塑件原材料分析  5
    2.3.1  PP材料特性与应用5
    2.3.2 塑件的公差与表面质量  5
3 拟定注塑模具结构 6
  3.1 分型面的确定6
  3.2 型腔数目的确定7
  3.3 拟选注射机型号8
    3.3.1 注射量的计算  8
    3.3.2 选择注射机  8
3.4 注射机相关参数的校核9
3.4.1 注射量的校核9
    3.4.2 注射压力校核9
3.4.3 锁模力的校核 10
4  浇注系统的设计 12
  4.1 主流道设计 12
  4.2 分流道设计 13
  4.3 浇口的设计 14
  4.4 浇注系统的平衡 14
5 推出机构设计  15
  5.1 推出机构的原则 15
  5.2 脱模力的计算 16
6 冷却系统的设计  17
7 合模导向机构设计19
  7.1 导柱的设计 19
  7.2 导套的设计 19
8 结构零部件的设计21
  8.1 成型零件的结构设计及计算 21
      8.1.1凹模的结构设计(型腔)21
      8.1.2 凸模的结构设计(型芯)22
  8.2 动定模板的长、宽尺寸的确定23                    暖风风洞挡板塑料模设计+CAD图纸:http://www.751com.cn/jixie/lunwen_17271.html
------分隔线----------------------------
推荐内容