毕业论文

打赏
当前位置: 毕业论文 > 化学论文 >

TBE温压炸药的力学性能研究+文献综述

时间:2018-08-24 11:36来源:毕业论文
采用理论分析与试验测试结合的方法,从静态和动态两个方面研究温压炸药(TBE)的力学性能。在组分相容的基础上,设计10个配方进行试验,发现当选用F橡胶作为粘结剂,粘结剂钝感

摘要本文采用理论分析与试验测试结合的方法,从静态和动态两个方面研究温压炸药(TBE)的力学性能。在组分相容的基础上,设计10个配方进行试验,发现当选用F橡胶作为粘结剂,粘结剂钝感剂比例接近0.6时,温压炸药的成型性最好,机械感度最低,强度最大。通过SHPB试验重点对温压炸药动态力学性能进行研究,分析结果发现:四种粘结剂下,失效应力值最大的是F橡胶,粘结剂与增塑剂的比例为0.6-1时失效应力和弹性模量最适宜,且改变粘结剂增塑剂的比例不能缩短药柱达到抗压强度极限的时间;对应力应变曲线进行分析,发现相对密度在95%-96%时,温压炸药的动态力学性能较好;通过分析得出,温压炸药具有明显的应变率效应。 27318
关键词  温压炸药,粘结增塑剂,SHPB,静态力学性能,动态力学性能
毕业论文设计说明书外文摘要
Title    Experimental Study on Mechanical Properties of  Thermobaric Explosives                                                
Abstract
Based on the theoretical and experimental methods, mechanical properties of Thermobaric Explosive (TBE) was discussed in this thesis, including static mechanical properties and dynamic mechanical properties. On the basis of components compatibility , 10 recipes were designed. The results showed that the TBE, made of the Viton as a binder and the radio of binders and plasticizer chose to 0.6, has lower mechanical sensitivity and higher strength. In order to investigate the dynamic mechanical properties, Split Hopkinson on pressure bar (SHPB) was performed. The results indicated that the TBE, made of the Viton as a binder and the radio of binders and plasticizer as 0.6-1, is the best for failure stress and elastic modulus. It can’t shorten the time to the failure value by the different the radio of binders and plasticizer. Analyzing the stress strain curve, the dynamic mechanical property is good when the density ratios are 95%- 96%. Through the analysis, the thermobaric explosive has obvious strain rate effect.Keywords  Thermobaric Explosive;binder-plasticizer;SHPB;static mechanical properties;dynamic mechanical properties
目   次
1  绪论    1
1.1  研究背景和意义    1
1.2  研究进展    2
1.3  本文的研究内容    3
2  粘结钝感体系性能分析    4
2.1 概述    4
2.2 粘结剂    4
2.3 增塑剂    7
2.4 本章小结    9
3  温压炸药静态力学性能研究    10
3.1 强度测试    10
3.1.1测试装置    10
3.1.2测试结果与分析    11
3.2 本章小结    14
4  温压炸药动态力学性能研究    15
4.1 分离式霍普金森压杆试验测试    15
4.1.1 试验装置和原理    15
4.1.2 试样制备    18
4.1.3 测试结果与分析    19
4.2 本章小结    27
5  结  论    29
致  谢    30
参考文献31
1  绪论
1.1  研究背景和意义
人们对炸药的应用需求,不断推动着炸药的发展。就战斗部应用的装药而言,炸药的发展经历了三个里程碑:第一代苦酸(三硝基苯酚),其熔点为121.8℃,需用过热蒸汽熔化,因此在高温环境下易造成危险;与弹体不相容,和金属作用产生一种敏感的苦酸盐,多次引起膛炸,造成人员伤亡和财产损失。因而人们不得不抛弃这种炸药,寻找合适的代用品。1863年德国Wilbrand.J制得了第二代炸药TNT(三硝基甲苯),1902年德国首先将其装填于炮弹,继而在第一次世界大战中发挥了重要的作用。这一时期炸药的特点是使用了可熔、半熔和不熔状态进行装填的混合炸药,使用了少量TNT,混合炸药的总能量不高,第三代炸药RDX便应运而生。随着火炸药科学技术的发展,在第二次世界大战期间使用RDX、特屈儿、太安作为军用混合炸药的组分,大大提高了混合炸药的能量。 TBE温压炸药的力学性能研究+文献综述:http://www.751com.cn/huaxue/lunwen_21783.html
------分隔线----------------------------
推荐内容